济南精华数控设备有限公司
【济南精华数控雕刻机】石材雕刻机_木材/墓碑/金属玉石专用雕刻机
全国客服热线:

0531-58566738

行业新闻

雕刻机出现错位怎么办?

  雕刻机在雕刻过程中出现各种错位缺点,如左右错位、上下错位、x轴错位、z轴错位等等,终究是什么缘由致使雕刻机出现错位表象呢?

  1.检查雕刻软件的途径正确与否;

  2.检查丝杆的空地巨细及光杆的紧固螺丝有没有松动;

  3.检查软件参数的设置正确与否。

  4.检查地线是不是接好

  5.电脑是不是有病毒或许与其他不兼容或许烦扰,一般主张无须品牌机简略拼装机箱即可

  6.水冷主轴电机前上方的联轴器是不是松动损坏可检查用手拧紧或许替换

  7.雕刻机横梁上到机器控制箱联接拖链的线是不是有接触不良

  8.驱动器的疑问:驱动器本身里面的布局或许电子原器材有疑问也会构成错位表象,这个缘由最多;若出现的次数不多,而且把速度下降一点,有时能正常雕刻,这说明驱动器还没有彻底坏掉;若是一开始雕刻就错位就说明驱动器彻底坏了。处理方法:修补驱动器或许替换驱动器。

  9.电压的疑问:雕刻机在作业时需求的功率大,若是电压过低,给驱动器供电缺少,功率达不到则会构成错位表象,这种情况一般以Y轴错位为多,出现这种表象有可能是外界电压不可,或许在同一线路上有人使用了大功率的设备如电焊等。处理方法:装置一个5000瓦的稳压电源,但这个稳压电源的过失规划不能超过5%,最好在3%以内。

  10.接口板,主板,转接板的疑问:要是接口板,主板,转接板坏了,雕刻机在作业的过程中,某一个方向或许是三个轴均不动,构成雕刻错位。

  主轴电机的疑问:要是步进电机或许是伺服电机的疑问,整个机器在某一方向上都不移动,用手转丝杆也转不动。

  11.机床本身的疑问:机床上的某个部件有疑问或许是松动,表面有杂质等也会出现错位表象;如联轴器松了,坏了,都会出现错位;导轨,丝杆上长期没有清洁加油也会出现错位表象;机床线要是断了也会出现错位表象。

  各部分联接控制线接触不良(功控线传输线)。处理方法:将全部连线拆掉再装

雕刻机

  In the process of carving, engraving machines appear various mismatches, such as left and right dislocation, up and down dislocation, X axis misalignment, Z axis misalignment and so on. After all, what causes it?

  1. the way to check the carving software is correct or not.

  2. check the hole in the rod and the fastening screws of the rod have not been loosened.

  3. check whether the software parameters are set correctly or not.

  4. check the ground line is not good

  5. computer is not a virus may be compatible with other incompatible or annoying, generally advocate without a branding machine simply assembled chassis can

  6. the coupling on the front of the motor of the main shaft of the water cooled main shaft is not loose and damaged, which can be checked by hand tightening or replacement.

  7. beam engraving machine to machine control box connected chain line is not bad

  8. questions: drive drive itself inside the layout of electronic equipment may doubt it will constitute the dislocation representation, the reason most; if the number is not much, but the speed drops a little, sometimes normal carving, the driver is not completely broken; if one starts carving dislocation that drive completely bad. Processing: repair the drive or replace the drive.

  9. questions: voltage power engraving machine in operation demand, if the voltage is too low, the lack of power supply to drive, not up to will be the formation of dislocation representation, this situation generally Y axis misalignment is much, this phenomenon may be external voltage can not, perhaps some people use high power equipment such as welding on the same line. Processing method: a 5000 Watt voltage regulator, but the fault planning of the voltage regulator can not exceed 5%, preferably within 3%.

  10. interface board, motherboard, transfer board question: if the interface board, motherboard and adapter plate are broken, the carving machine may be three axis in one direction, which will form a sculpture dislocation.

  The question of spindle motor is that if stepping motor is probably the doubt of servo motor, the whole machine will not move in a certain direction, and it will not be able to move by hand.

  11. questions: a machine parts on the machine in question may be loose, surface impurities also arise such as dislocation representation; coupling loose, broken, will appear on the screw dislocation; guide, no long-term clean fuel will also appear dislocation representation; machine tool line is broken will dislocation representation.

  Each part of the connection control line is in bad contact (the power line transmission line). Treatment: remove all the wires and reload

联系我们

联系人:吴经理

手 机:13791100065

电 话:0531-58566738

邮 箱:2789920644@qq.com

公 司:济南精华数控设备有限公司

地 址:山东省·济南市